The Remote Garage Opener in the BMW models is located near the moonroof switch, or under the rear view mirror. There will be 3 buttons, numbered 1,2, 3.

HomeLink ® Programming for Garage Door. Programming instructions are what you will need to follow inorder to program your garage door opener to your car's. Trying to program your HomeLink for your BMW? For BMW owners who are using a garage door opener by Genie, Sommer, or who have an older generation of HomeLink. You have just purchased a new BMW and want to know how to program a BMW garage door opener. Remote garage door openers are very convenient and make it easy to access.

Step 1: make sure your BMW is either inside or outside of the garage and NOT under the garage door! Step 2: Insert the key and turn the key until all the gauges light up, without starting the car. With the key fobs, push the 'start' button,without your foot on the brake, until the gauges light up but not starting the car. The BMW garage opener will NOT program if the BMW engine is running. Step 3: Press and hold the two outside buttons (#1 and #3) on the garage opener by the moonroof switch or under the rearview mirror. Continue to hold both of the buttons down until you see a small light beside the #1 button begin to blink rapidly. This usually takes 30 seconds or more.

Then release both buttons. Step 4:Take your house garage remote, hold it very close to the BMW's #1 button, and then press your house remote and the #1 button down at the same time, and continue to hold them down until you see the small light by the #1 button begin to blink again rapidly. Then release both buttons. Step 5: Press the #1 button on the BMW, and if the garage door starts up or down, then you are finished. If nothing happens.go to Step 6 Step 6: With the BMW gauges still lit up as before, get a small step ladder so that you can reach the garage door motor near the garage ceiling. Depending on the type of garage door unit, there will be some buttons on the rear of the unit, or in the front of the unit near the garage light. Locate the button that has 'learn' or 'program' labeled beside it.

Press that button on the unit and it will start blinking, or either just light up red. Step 7: Then get down and go back to the BMW. Press the BMW #1 button and hold it down for 3 seconds, then release it. Press and hold the same #1 button down again for 3 seconds and release. Repeat this step a few more times until the garage door starts up or down.

Then it is programmed. After that all you do is press the #1 button to open and close the garage door. For multiple garage doors, repeat Steps 4-7 for the BMW button # 2 and #3.

Mike Appling has driven BMW's since 1973 and has been in sales at Athens BMW in Athens, Georgia since 1984. For 10 consecutive years, Appling was awarded the prestigious BMW of North America's 'Grand Travel Award' for serving as one of the Top 50 BMW Client Advisors in the nation, based on number of BMW's sold, customer satisfaction ratings, and amount of BMW training. In addition, Appling has served on the BMW of North America National Sales Councils and Professional Sales Councils. Visit my website at www.mybmwguy.com.

Manuale Di Conversazione Campanile Pdf. 5 Steps To Program Your HomeLink ® System ​​Note: Some vehicles may require the ignition be turned on or the vehicle actually running to program the Homelink ® transceiver. To program a rolling code compatible Homelink ® system, please follow these steps.

If you have a newer garage door opener from Overhead Door ® garage opener, including a Destiny ®, Odyssey ®, or Legacy ® 850 and the first 5 digits of the serial numbe​rs are 11291 or greater please find our.​ For any serial number smaller than 11291, the following programming instructions are what you will need to follow inorder to program your garage door opener to your car's HomeLink ® system. • Press and hold the two outside buttons on the Homelink ® system until the LED starts to blink, release buttons.

• Press and hold the desired Homelink ® button and the transmit button on your rolling code transmitter at the same time until the Homelink ® LED changes from a slow blink to a rapid blink. (Your Homelink ® system is now programmed) • Locate the learn code button on your garage door opener. (These are located under the light cover or on the rear panel depending on model) • Press the learn code button on the garage door opener, a red LED will start to blink. (You will have 30 seconds to complete programming) • While the LED on the garage door opener is blinking, return to the vehicle and press the pre-programmed Homelink ® button 4 times. (Or until the garage door operates). Need to purchase a new garage door opener that works with HomeLink ®​?